How to make flying chinese lanterns

how to make flying chinese lanterns

Jun 22,  · How to Make Chinese Paper Lanterns ??. To make Chinese hanging paper lanterns you need the following basic materials. Sheet size A4; Pencil; Scissors; Rule; Glue; Colored Papers; Felt-tip pens; Thread; Start by folding a piece of paper horizontally in half. Then make cuts with the scissors on this folded paper but never reach the edge of it. Measure each strip for 12” wide and 24” long. On each strip end, lay the measuring tape flat and cut in at 2” and 10”. Measure a half an inch in and cut a small strip so each strip edge folds up. Construct the Lantern Place 12” metal ring on top of two pieces of tissue paper.

This Fall do something unique, creative, and FUN! This event brought together thousands of participants to release chinese lanterns into the night sky. How cool, right?!! Culturally, the release of Chinese lanterns symbolizes putting dreams and goals into the action or celebrating the life of a loved one or even simply wishing for good luck. Today, we want you to make your own Chinese lantern to release your own hopes and dreams into the world! Ready to make your own Chinese Lantern?

Check out her DIY video with helpful step-by-step instructions. Instructions Lay tissue paper flat on the floor and cut into 4 even strips.

Measure a half langerns inch in and cut a small strip so each strip edge folds up. Add Mod Podge to edge folds on each side of the tissue paper and cihnese around the edge of the wire. Repeat until both tissue paper pieces are secure around the edge of the ring. Next, repeat and glue two other tissue paper pieces to second ring. Once both rings have papers around them, glue ends together to create a cylinder.

Secure ends with kraft paper tape. Repeat on other end of cylinder. Secure with kraft paper tape. Create flyinb light! Fold 2 sheets of paper towel into a square shape and soak in candle wax.

Once dry, poke two what should my fasting blood sugar be with gestational diabetes through the ends of the paper towel and attach to one end of the base. Safety Tips Make sure to release your lantern in a safe, open space. Be sure to have a fire extinguisher ready in case of any issues. Note please make sure to only use biodegradable materials when making these items.

See you there! No thanks!

Sky Lantern Autopsy

How to Make Chinese Flying Lanterns. Step 1. Fireproof the blue tissue paper since it will be used for the bottom of the lantern that will be near open flame. Hang the tissue paper on a Step 2. Step 3. Step 4. Step 5. That ounce, added to the paper-lantern's original weight of ounces, added up to a maximum flying weight of ounces for a lantern with this internal volume. It is the internal volume of a paper hot-air balloon, and the heated air it can contain as well as how much that air is heated, which determines its maximum carrying capacity. Jan 01,  · Lanterns from Amazon: freedatingloves.com sky lanterns, UFO quality, absolutely mesmerizing to watch as sky lanterns float gracefully into the.

View cart. How to Make Sky Lanterns Can mere mortals make sky lanterns? I gotta admit, I've seen sky lanterns around for several years. I've seen 'em advertised right here by Skylighter. Have seen them at displays and club events. But, honestly I never gave them much thought, and I wasn't much tempted to buy any.

But, then I saw the latest Skylighter ad for them, and I thought, "I wonder how sky lanterns are made. I watch This Old House and The New Yankee Workshop , just to see how they do stuff, even though I've been doing that kind of work myself for a living for 30 years. So, I had Harry send some of the flying lanterns to me. By the time they arrived on my doorstep, I was excited to see them. I opened the package up, looked at the treetops to make sure there wasn't too much wind blowing, and I hustled my wife and granddaughter outside to fire the first one up.

I enjoyed finding out how to light the paper lantern, and how to let it inflate and launch it. And, the three of us really did have fun watching it lift off, and then gazing at it for minutes until it flew out of sight and we couldn't see it any more. Then I quickly got another one out and launched it as well. My son and his family came over last Sunday, and I knew I just had to demonstrate these new toys for my grandsons.

The photos below say it all. Note: I'm gonna tell you how I ended up successfully making these homemade paper hot-air balloons. But, as with any pyro project, I learned some lessons the hard way, and I had some significant failures.

I'll note these as I go along in this hot paper tale. Sky Lantern Autopsy A little reverse engineering revealed: Weight of a flying lantern 2. In between each Z-fold of the waxed cloth are five 2. Maybe the young Chinese lady who made this one was wearing some fragrant perfume. Note: I have also seen sky lantern burners, which resemble fiber-reinforced blocks of wax.

I don't know how they are made and have not tried to duplicate them. The "bag" of the balloon is made up of white tissue paper. This paper has been treated with a fire retardant; it does not catch fire when touched by a flame. It just scorches a bit. The tissue paper bag weighs 1.

There are four panels called gores in the ballooning world that make up the balloon, and they are glued together and to the bamboo hoop.

Here's a sketch of one of the gores, with a bit added to the edges to allow for gluing. I tethered the Chinese lantern to a weight with some very thin, light string as it burned. The fuel pack burned for 4.

I added 0. That 0. It is the internal volume of a paper hot-air balloon, and the heated air it can contain as well as how much that air is heated, which determines its maximum carrying capacity.

Skylighter Sky Lantern Carrying 0. These flying lanterns are delicately balanced for flight, and they are just light enough to allow them to fly. If they were much heavier, they would not leave the ground. Due to some circumstances, which I describe below, my first balloon ended up weighing 3. So, let's make a paper sky lantern I went up to my local Hallmark store and bought some nice tissue paper in different colors. Some checking online produced some leads on products designed to flameproof paper.

One company, Universal Fire-Shield www. I ordered some. This would be enough to treat about a dozen paper hot-air balloons. Tissue Paper, and Fireproofing Product I hung 4 pieces of the red tissue paper on a clothesline, and sprayed them with the Paper Shield until they were saturated. After they were dry, I tried to burn a little piece of the paper, and it only scorched like the original fire-lantern paper, but it would not burn.

Fireproofing the "Laundry" Note: On my third attempt to make one of these paper lanterns, I decided to try to spray the untreated bottom half of the balloon after it was assembled, in order to skip the step described above. I hung it up, slightly inflated it with my heat-gun, and started spraying it.

The tissue paper soon started to weaken, sag, and tear, ruining the balloon. Another lesson learned. I decided that the process of hanging the panels like laundry works best. The upper corners of the sheets will be cut off when the gores are cut out, so I don't spray those areas because they get weak when they are wet, and allow the clothespins to tear through the paper and sometimes that has the paper to tear loose from the string. Warning: Paper Shield has an acid in it, and it will damage a concrete garage floor slightly.

It's best to have a plastic drop cloth under the clothesline to protect the floor. Don't breathe its fumes or get it on your skin. The red tissue will be the bottom of the paper hot-air balloon, which will be the only part that gets exposed to the flame. The top of the balloon will be blue paper, and it does not need to be treated.

I glued a piece of the red paper to a piece of the blue with thin stripes of Elmer's, and I did that four times for the four panels, and let the panels dry. Note: The Elmer's glue tends to wet the tissue paper, bleeds through, and tries to stick to the other stuff around it.

In an attempt to avoid this problem, I used hot glue when building my first balloon. This worked nicely during construction, but when I fired that baby up, the hot-glued seams at the top of the balloon let go completely. I did not think the internal temperature would get high enough to cause this problem.

I was wrong. My wife, Molly, told me later on that she wondered about me using the hot glue, and that she thought it would melt when the burner was lit. Oh, well. The hot glue, which is significantly heavier than the dried Elmer's, also contributed to the excess weight of the first model. After gluing the red and blue sheets together and letting them dry, I cut the four panels out with scissors, using a kraft paper template that I made based on the sketch above. Folding the kraft paper in half lengthwise, and then every 6" made the pattern transfer easy.

The outside of the gore is simply the side that I think looks best. Then I laid a gore, outside up, on top of the first gore, weighed the two down, and glued the right sides together with a thin stripe of Elmer's. The table had waxed paper on it so that any glue that seeps through wouldn't stick to it.

I then folded the top gore's loose side over on itself, so that half's inside was facing up, inserted some waxed paper between the glued side and this loose side, and laid the third gore on top of that one. I glued those two loose edges together, inserted more waxed paper, folded the loose half of the third gore over, laid the fourth and final panel on top, and glued those loose edges.

Then the last step was to fold the loose half of the top, fourth gore, over on itself, and fold the loose half of the bottom, first gore over onto it, and glue the loose halves together. This all sounds much more complicated than it actually is. Once you try it, it'll all make sense. Then I pulled the glued edges up and off all the waxed papers, propped the panels apart from each other and from the table, and allowed the seams to dry.

I let the seams dry, and then I tried to turn the bag right side out, so that the seams would be hidden. This probably would have worked OK, but the fireproofed red tissue paper was somewhat brittle because of the fire-treatment, and as I tried to turn it inside out, it started to tear and crack at the bends and creases. I had to try to repair these tears with clear packing tape, which increased the lantern's weight, and made it ugly, and not something to be proud of. I decided to simply allow the seams to be on the outside of the bag in future models, and avoid the "turning inside-out" step.

Making the sky lantern's bamboo hoop Home Depot had some 1" diameter bamboo poles in their lawn and garden department. I bought one and carefully split it into thin strips. I took one of the strips and smoothed it with sandpaper and a razor knife until it was about the dimension of the original lantern's bamboo.

I only sanded the "interior" side of the bamboo because I did not want to weaken the smooth, exterior side of it.

Then I glued it into a hoop with the same circumference of the original. These are often split to obtain bamboo strips for girandola frames, wheel frames, and the like.

Or you can steal some green bamboo from Harry Gilliam's bamboo-infested front yard. Making the Sky Lantern Burner I had some blue, industrial paper-towels, and I decided to melt some grocery-store canning-wax, and impregnate the towels with the wax in an attempt to duplicate the waxed fabric that I found in the original fire-lantern's burner.

Warning: Canning paraffin wax is very flammable, and should only be melted over low heat in a double boiler. It should never be exposed to open flames or high heat. Coating a Paper Towel With Wax to Make Sky-Lantern Burner I took a strip of this waxed paper towel, and burned it alongside a strip of the waxed material from the original lantern's burner.

Both samples burned identically and for the same amount of time. I had some coarse, recycled kraft paper, and cut it into rectangles to match the original burner's paper layers. Then I cut some strips of the waxed paper towel to match the original burner, and sandwiched 5 pieces of the kraft paper in between each layer of the waxed paper-towel. Then I stacked the layers of the burner together, punched 4 holes through all the layers with an awl, and threaded two pieces of wire through the holes.

The ends of the wire were then wrapped around the bamboo hoop and twisted tightly to secure the ends. The hoop was then carefully glued into the end of the lantern's tissue paper bag, and the glue was allowed to dry.

Then strips of cotton-ball like material can be saturated with rubbing alcohol, draped over the center of the wire X, and ignited when launching the balloon.

1 thoughts on “How to make flying chinese lanterns

Add a comment

Your email will not be published. Required fields are marked *